The Ultimate Guide To Double Glazing Door Lock Repairs
The Ultimate Guide To Double Glazing Door Lock Repairs
Blog Article
Double Glazing Door Lock Repairs
Have you noticed that your uPVC window or door mechanism started to fail? Perhaps the handles on your uPVC windows and doors aren't aligned properly or are difficult to use.
You'll lose energy in the event that your double-glazed doors fail to perform as they should. This increases the likelihood of burglaries. Owen the Locksmith will be able to fix your door lock at an affordable price.
Snapped Key
It can be a hassle when a key is snapped into the lock. It could also be a security risk, as the door may not lock and could leave you open to intrusion. There are a couple of quick fixes you can make to resolve the issue and make your door work again.
Be sure to remain calm. If you panic and begin doing a lot of fumbling around you could end up pushing the damaged piece of the key even further into the lock, making the situation much worse.
Spray WD-40 or another penetrating oil, into the lock. This will assist the broken piece to emerge more easily. You can also use a screwdriver to help break up any stuck pieces that could be hindering the flow. If you have a piece of the key stuck out and is not being removed, grab it with a paperclip or other thin metal object and pull it. Both of these methods work, but be careful not to push the broken piece of the key even further into the keyway.
Some paperclips have grooved edges that could serve as a hook extractor, and some Jigsaw blades also work for this use. If you don't happen to have one of these tools you can bend a hook using needle-nosed pliers. Additionally, you can make use of a pair of tweezers to grab and pull out the remaining pieces of broken keys.
If you are unable remove the broken key piece then you can use a lock deicer. This is usually found in most hardware stores. It is used to freeze any water or ice that could be in the lock.
If none of these solutions seem to work, it could be time to consult a locksmith. Fitlocks experts can quickly fix issues such as broken handles and snapped keys using uPVC locks and door mechanisms. They can also reconfigure the double glazing door mechanisms so that they are simpler to operate. Get a double glazing repair through us online, or give us a phone call to discuss your requirements.
Broken Cylinder
A damaged cylinder can pose an extremely risky security issue. It's fortunately a simple repair for a professional locksmith to complete. To fix the cylinder, a locksmith will need to tap it. This can be done with a hammer or other tool. However, the best method is to employ a wire or long match. Then, position the end of the match or wire near the keyway. The locksmith will then strike the lock to break it. This is much better than using a hammer that can harm the lock.
The most frequent cause for cylinder head cracks is overheating. This can occur when the block and cylinder head are made of various metals like cast-iron and aluminum. When the different metals heat up and cool down at different rates, it may create hotspots in the local area that expand faster than the rest of the cylinder head, thus leading to cracks.
Corrosion is a different cause of cylinder fractures. If the cylinder head and cylinder block are not properly maintained, it can lead to rusting or corrosion, which may cause them to expand at a more than they ought to. In time, this could also lead to cracks.
If your uPVC door or window lock is stiff or requires an enormous amount of pressure to turn, it can be the result of several things. A malfunctioning locking mechanism, misalignment or an old handle are the most common causes of this problem.
This is a simple and cost-effective fix that a majority of double glazing owners can do. A professional locksmith should be able solve this problem within an hour after arriving at your residence. Depending on your needs they can change the locking mechanism, replace the window handles, and also change the gearboxes. A locksmith with experience will always be able advise you on the most cost-effective options for your home. They may suggest upgrading to 3 Star TS007 Euro Cylinders, which offer an additional security layer from burglars. It's a small price to pay for the peace of mind that comes from knowing your uPVC doors are safe.
Broken Handle
Window double glazed window suppliers near me handle locks have intricate mechanisms that deteriorate with time and use, so it's no surprise that they sometimes break. If yours breaks it may be difficult to pinpoint the cause of the issue and make sure you fix it properly.
Repairing your damaged handle, whether it's an internal locking mechanism or latch will increase the security of your uPVC door and stop draughts. If you do not repair or replace the handle could be expensive and could cause damage to the door's frame and lock, so it's worth taking some time to do it right.
With the window open, loosen the screw that secures the handle using the screwdriver. It should be located on the inside of the back plate, normally hidden by a screw cover for aesthetic reasons. Be sure not to double glazed windows near me lose any internal parts within the handle, for example the plates or levers on either side of the spindle. Ideally, keep them in the same order so that you can re-install them if needed.
Then, with a second screwdriver take the screw off that holds the handle to the spindle on the back. Once this is removed, you should be capable of pulling the handle away and pull out the broken spindle. Replace it with a brand new spindle, making sure it's the same length (you can purchase them online or in hardware stores). Securely screw it in the correct position. Be cautious not to overtighten because this could damage the handle or the window frame.
Check that the new handle is fitted, then close and test the handle. Hopefully, it will work smoothly and you'll be able unlock your window.
Don't forget to double-check that your double glazing units near me uPVC window is closing properly while you're working with the handle. If they don't then you may experience damp and draughts inside your home, as well as compromising the efficiency of your home's energy usage. Core Sash Windows is a local window company that can alter the hinges of the window frames to ensure that they close correctly.
Broken Spindle
It is quite common that the spindle in a handle breaks rather than the handle itself. This is especially common with uPVC tilt-and-turn windows. These windows require a handle that is a lock mechanism that is located in the frame of the window. The handle is attached to a central rod that triggers the mushroom-shaped locking cams that secure into the frame of the window keep. If the dead latch mechanism does not open when the handle is turned, it's likely the spindle has been damaged. This can be a frustrating problem.
There are solutions to this issue. A reputable locksmith can quickly and efficiently repair this problem. A professional locksmith can disassemble the window's handle using a tool to take out the wheel portion in which the spindle is. This can be done without causing any damage to the handle or causing any other damage to the window frame.
After removing the wheel the technician will inspect the spindle and identify the cause of the break. This involves disassembling the spindle and examining each component part, noting any damage or excessive wear. This procedure is typically performed by technicians in a clean environment.
The next step is to clean the damaged spindle, this will remove any debris or dirt that could be hindering its normal functioning. double glazed window suppliers near me After that, the spindle can be repaired or replaced. If it is being replaced the technician will need the dowel that is similar in size to the original and drill mating holes in both pieces of replacement double glazed units near me the spindle. This ensures that the new spindle has precisely matched to the handle.
If the damaged spindle can't be repaired, it could require replacement completely. Home centres sell generic replacements. However, If the style of your window is unusual then it will be necessary to speak with a woodworker or cabinet maker who can duplicate the exact model for you. Once the spindle has been installed, it is connected to the handle. The screw holes on the handle to the screws already in the frame. Once the new handle is seated you will be ready to operate your uPVC window.